Raven 2.4m inclined orbit motorised dish.
Raven 2.4m dish, inclined orbit polar mount using two actuators.
Technical - Gain 47.6 dBi at 11.95Ghz. 3dB beamwidth - 0.7 degrees. Cross polarisation - 30dB, collar fits a 100mm pole.
Weight of polar mount 29Kg. Weight of actuators 12Kg. Total motor weight 41Kg. Heavy duty Raven fibre glass dish.
The one piece reflector is thermoset-molded glass fiber reinforced polyester for strength and rigidity and surface accuracy.
These Raven Skyware Global dishes were formally "Andrews dishes" and before that "Channel Master".
An ultimate dish for enthusiasts. For moving east and west, a genuine heavy duty SuperJack
36 inch actuator is included.
The
18 inch heavy duty HR actuator is for up and down adjustment. This is ideal for tracking inclined orbit satellites.
Two positioners are needed. These can be a Primesat V Box for control of east and west positioning using a modern
satellite receiver in automatic mode and a 2nd V Box in manual mode for up and down elevation acting just as a positioner.
Manual mode would be using the handsets which came with all V Boxes. All satellite positions can be stored. For inclined
orbit satellites a timing chart is useful (
ring us for further advice).
The
inclined orbit motor kit is available separately.
About the motor unit - This motor unit is produced by our sister company
www.primesat.eu
for the Satellite Superstore.
It is designed for the 2.4m Raven dish. The "dish back plate frame" is etch primed, primed, powder coated and baked in
an oven to provide a durable finish. The rest of the polar mount including the collar is dipped galvanised. All of the nuts
and bolts are made of stainless steel except the main elevation adjuster which are made of brass. The polar mount includes
a frame which is designed to fit on the back of the Raven 2.4m dish using the 4 bolts which come with the Raven dish.
A matched Raven feedhorn is recommended. This feedhorn with a C120 flange LNB will provide better matching and more
good signal (higher signal to noise ratio) than a standard 40mm clamp LNB. It is best not to invest in a high quality Raven
dish and use a compromise 40mm mass market LNB where the integrated feedhorn is designed for
ANY dish but is not
matched? Taking this 2.4m dish as an example, a 40mm LNB may only illuminate 2.3m of dish area or perhaps 2.5m of dish
area (i.e. including noise from round the edges) but with a matched feedhorn, exactly 2.4m of dish area is illuminated.
Spare parts are available for the Raven dish - fixed
AZEL mount, spare
arms, and the 40mm/23mm
feed support boss.
4 core motor
control cable for these motors is available.
If you already have a 6.5" pole, a
pole adapter is available.
V Box options. Using a Diseqc satellite receiver, a
V Box is also needed, or a V Box can just be used as a
separate positioner as it comes with it's own remote control. The V Box in automatic mode converts Diseqc
commands to 36 volt positioning and only the satellite receivers remote is used. It also introduces more power to
drive heavier duty 36 volt motors. 2 V Boxes are needed. See options below.
LNB options below. There are many LNB options. LNB not included unless an option is chosen. There are 40mm
clamp universal LNB options. If a wideband LNB is to be required, choose the hybrid 40mm LNB as it has universal
outputs as well. If wideband LNB outputs are required they must be 40mm and there are no c120 flange wideband
LNBs available. This is also the case with the fibre headend.
Feedhorn c120 LNB options. When using universal LNBs, the matched feedhorn and c120 flange LNB is best. A
matched feedhorn will maximise signal capture in low signal locations and is available with several c120 flange LNB options
Ground stand.
ground stand is available separately.
Non-pentrating ground stand. A heavy duty Primesat non-penetrating
ground stand is available separately.
C Band LNBs can be selected separately by ordering a C band stainless steel feed
support clamp and a
C Band LNB
A
standard polar mount motorised version and a
fixed version of this 2.4m dish are also available.
Shipping information and options. (
VAT info.) (
Stock levels.)
Choose "
free* mainland UK delivery" - UK shipping
option No 1 (see exception below*)
* Free mainland delivery to most postcodes but some postcodes, highlands and remote locations may require a surcharge
All UK offshore islands. Shipping will carry an additional surcharge.
Email or
ring 01207 544664.
All internationals. Shipping to all destinations is by quotation.
Email or
ring +44 1231 544664 (GMT).
Raven 2.4m inclined orbit dish, polar mount,
heavy duty 36 inch actuator, 12 inch HR actuator
Order code RA24IPMA
£4569.95
Options, if required, will be automatically added to the dish when you "add to cart" below.
If you are outside of the UK, a 20% VAT refund will be done before shipping.
Raven 2.4m motorised dish options. Click on picture for more Info.
Raven Spare Parts.
Raven Spare Parts -
arms / legs for Raven 2.4m dish.
These arms are included when you buy the Raven dish but if you have an old Channel Master (or Andrews)
dish for many years dish and the arms need replacing they are available separately here.
These are the 3 arms which go between the dish reflector and the LNB feed support clamp.
Please note the picture shows the arms for the 1.8m dish but the 2.4m arms are longer but similar.
Click here to order.
Raven feed support boss.
This is the feed support clamp that fits on the ends of 3 arms of the Raven
(formally Andrews and before that Channel Master) 90cm, 1.0m, 1.2m 1.8m and 2.4m offset dishes.
This is a 40mm clamping LNB support boss. Bolts nuts and washers are included.
In stock and ready for immediate shipping.
Raven feedhorn support boss assembly
In stock and ready for immediate shipping
Click here to order.
C Band Feed Support Boss for Raven Dish.
Designed for the
Raven fibre glass offset dishes,
1.2m, 1.8m and
2.4m
Note, Raven dishes were formerly "Andrews" and before that "Channel Master".
This is a high quality stainless steel bracket / feed support boss for C Band LNBs with an offset feedhorn.
At last a very high quality product for fitting C band LNBs onto the Raven offset dish.
Click here to order.
See our other web site at-
www.primesat.eu
This site includes many products that are exclusive to the Satellite Superstore.
The site contains -
• Products that we manufacture (e.g. We have manufactured heavy duty wall mounts and ground stands since 1991).
• Selected products which have our own Primesat brand name and have been prepared to our specifications.
• Selected products where we have been appointed the authorised UK or European distributor by the manufacturer.
www.primesat.eu is an information site. Here you will find full specifications and many detailed pictures.
To buy any of these products, simply order them on this web site.
Link to our own satellite museum site
Satellite Museum. A museum of vintage satellite receivers.
See www.satellitemuseum.com
For old satellite receivers with knobs on and read about "A History Of Satellite TV".
Also see
www.rewindmuseum.com. A Museum of vintage consumer electronics.
Vintage reel to reel video recorders. Vintage VHS and Betamax VCRs. Vintage video cameras. Vintage
Laser Disc. Vintage Computers. Old telephones. Old brick mobile phones. Vintage Hi Fi, Old reel
to reel audio and early audio cassette decks. Including, the history time line of vintage
consumer electronics ... and much more .....
It is well worth a visit.
Only The Satellite Superstore brings you
great products, advice and it's own museum.
You may be interested in two other web sites.
www.1952chevytruck.com
This web site shows all of the restoration process and the modifications to this truck.
In addition, there is a hard high quality tonneau cover on a new web site
at www.classictonneaucover.com for the 1947-53 Chevy truck.
Contacting us.
Unlike many other companies we are happy to answer questions on the phone.
Tel. (UK) 01207 544664 and 01207
544224
International Tel. + 44 1207 544664.
Before sending questions via e-mail please check-out our
Frequently Asked Questions as
this could save
time.
If you have any questions & comments regarding this site's content, or you need advice please ....
click here to go to our contact forms.
Copyright © 2019 Vision International. All rights reserved.